Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
tutorials [2019/11/19 22:43] lrodriguezp |
tutorials [2020/03/04 09:59] (current) admin [Electronics] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Tutorials ====== | ====== Tutorials ====== | ||
| + | |||
| ===== Projects ===== | ===== Projects ===== | ||
| Line 29: | Line 30: | ||
| [[tutorials:api_doc_generation| Automatic API documentation generation]] | [[tutorials:api_doc_generation| Automatic API documentation generation]] | ||
| + | |||
| + | [[https://github.com/trein/dev-best-practices/wiki/Git-Commit-Best-Practices| git commit best practices]] | ||
| ===== Copters ===== | ===== Copters ===== | ||
| Line 71: | Line 74: | ||
| ===== Linux Installation & Software ===== | ===== Linux Installation & Software ===== | ||
| + | [[tutorials:Image Ubuntu 18.04.3 server arm64 for Raspberry Pi 3b with GPIO zero and I2C activated. Ros Eloquent Installed.]] | ||
| + | |||
| + | [[tutorials:Activate GPIOzero and I2C pins in Raspberry Pi 3b with Ubuntu 18.04.3 server arm64]] | ||
| + | |||
| + | [[tutorials:ubuntu_18.04.3_server_ros_dashing_rpi3b | Ubuntu 18.04.3 server with ROS Eloquent RPI3b]] | ||
| [[tutorials:debian_buster_for_rpi3_with_qemu|Debian Buster for RaspberryPi 3 with Qemu in 64bits (aarch64)]] | [[tutorials:debian_buster_for_rpi3_with_qemu|Debian Buster for RaspberryPi 3 with Qemu in 64bits (aarch64)]] | ||
| Line 132: | Line 140: | ||
| [[tutorials:emacs_for_python|How to configure GNU/Emacs for python development]] | [[tutorials:emacs_for_python|How to configure GNU/Emacs for python development]] | ||
| ===== Prototype Hardware & Software ===== | ===== Prototype Hardware & Software ===== | ||
| + | |||
| + | [[tutorials:pcb_design_tips|PCB design tips]] | ||
| [[tutorials:impresora3d|Impresora 3D Ultimaker]] | [[tutorials:impresora3d|Impresora 3D Ultimaker]] | ||
| Line 188: | Line 198: | ||
| [[tutorials:development_of_a_low_cost_laser_range_scanner_for_underwater_applications|Development of a low cost laser range scanner for underwater applications (collaboration with the STRI)]] | [[tutorials:development_of_a_low_cost_laser_range_scanner_for_underwater_applications|Development of a low cost laser range scanner for underwater applications (collaboration with the STRI)]] | ||
| + | |||
| + | ===== Linux general tricks ===== | ||
| + | |||
| + | [[linux_tricks:latex|Latex tricks]] | ||
| + | |||
| + | [[linux_tricks:emacs|Emacs tricks]] | ||
| + | |||
| + | ===== Special Equipment ===== | ||
| + | |||
| + | [[tutorials:oscilloscopes|Oscilloscopes]] | ||
| + | |||
| + | ===== Workshop ===== | ||
| + | Soon..stay tuned | ||
| + | |||
| + | ===== Guide for writing theses ===== | ||
| + | |||
| + | [[tutorials:theses_writing_guide|Thesis writing guide]] | ||
| + | |||
| + | ===== General Knowledge ===== | ||
| + | |||
| + | ==== Mechanics ==== | ||
| + | |||
| + | [[tutorials:bolts_and_screws|Bolts and Screws]] | ||
| + | |||
| + | ==== Electricity ==== | ||
| + | |||
| + | ==== Electronics ==== | ||
| + | |||
| + | ==== PCB connectors ==== | ||
| + | |||
| + | === Jtag 0.05" (1.27mm) 2x10 connectors === | ||
| + | |||
| + | Samtec FTSH series with -k (keying shroud) | ||
| + | |||
| + | https://www.digikey.de/product-detail/en/samtec-inc/FTSH-105-01-F-DV-K-TR/SAM13160CT-ND/8827915 | ||
| + | |||
| + | https://eu.mouser.com/ProductDetail/Samtec/FTSH-105-01-F-DV-K-TR?qs=sGAEpiMZZMs%252BGHln7q6pm8Vn94ktop%2FJcWvxRfJNmxFIS9LnArsO%2FA%3D%3D | ||
| + | |||
| + | mouser doesn't show the correct picture | ||